Joyetech eGrip VT applies with the Variable Temperature Control system, supporting VT-Ti/ VT-Ni/ VW mode with an OLED screen.It gathers all the advantages of the original eGrip but easier to clean now.
Notice: Joyetech now requires S/N (serial number) before providing replacements (due to counterfeits in market).
We recommend you to keep the packing boxes after you get parcel, or take a picture of SN before you discard it. Thank you!
Shipping restriction: due to exclusive distributor of Joyetech, we do not send Joyetech products to customers in Russia, South Korea or UK.
We just received a Christmas Edition from factory, which comes with an extra "Merry Christmas" cover. And we'll ship 2 versions randomly.
30W Joyetech eGrip OLED VT Kit - 1500mAh
30W Joyetech eGrip OLED VT MOD, applies with the Variable Temperature Control system, supporting VT-Ti (Titanium)/ VT-Ni (Nickel-200)/ VW mode with an OLED screen. It also boasts a 360-degree regulation ring to adjust output wattage or temperature. The compact size with multiple colors catering to your preference makes it always comfortable to hold.
Size: 46.4mm*20.4mm*99.5mm (including mouthpiece)
Battery Capacity: 1500mAh
Output Mode: VT-Ni/VT-Ti/VW Mode
E-juice Capacity: 3.6ml
0.2-1.0ohm for VT mode
0.4-3.5ohm for VW mode
Joyetech eGrip OLED VT Kit comes with
Variable Temperature Control
Supporting VT-Ti (Titanium)/ VT-Ni (Nickel-200)/ VW mode
360-degree regulation ring
Easy to clean
1. Power on/off:
Press the fire button 5 times in quick succession to turn the device on.
In the same way, the device will be powered off after 5 presses.
Hold the fire button and inhale through the mouthpiece. Release the Fire button and exhale.
3. Shift between VT-Ni/VT-Ti/VW Modes:
Press the fire button for three times to shift between VT-Ni/VT-Ti/VW Modes when the battery is on.
(1)under VW mode, it presents: battery life, ohm, voltage and wattage.
(2)under VT mode, it presents: battery life, ohm, wattage, temperature and mode (Ni/Ti).
4. Adjust the wattage/temperature:
Under VW mode, rotate the ring around the button clockwise or counterclockwise to increase or decrease the wattage (5W-30W); under VT mode, rotate the ring around the button clockwise or counterclockwise to increase or decrease the temperature (100-315℃/200-600℉).
Rotate the ring faster clockwise or counterclockwise for continuous three grades, the device automatically increase or decrease 0.1W/5℃(10℉) numerically.
5. Regulation of air-inlet:
Spin the adjustment screw on the side of the button. Counterclockwise rotation will loosen the screw. The looser the screw is, the larger the air inlet is.
6. Atomizer head replacement:
Unscrew the cap on the bottom with the tiny tool in the box (or just a coin), you’ll see the atomizer head located right on the base. Then replace the head with a new one.
7. e-Juice Filling:
Push up the lid on the side of the body, then slowly refill the liquid into the hole. (Note: Don’t forget to lock the cap after finishing it.)
8. Vent Pipe Cleaning:
The vent pipe of eGrip VT is detachable. Take off the mouthpiece then use the tiny tool in the box (or just a coin) to unscrew the vent pipe from the top so as to clean it individually.
Plug into the charging port at the bottom. It usually takes 2.5 hours to fully charge the battery via 1A wall adapter.
1.Screen: The OLED screen presents watts, ohms, temperature, battery life and timing while vaping.
2.No Atomizer Alert: When the coil is not installed properly, the screen will appear “No Atomizer”.
3.New Coil Alarm: When installing a new coil whose resistance is larger than the previous one to some degree, resetting the “basic resistance” (resistance at room temperature) shall be required.
After fitting a new coil, press the fire button while the atomizer base is removed to initiate a reset. After you reinstall the atomizer base with a new head, the screen will appear “new coil up, same down”. Rotate the regulation ring clockwise to confirm that a new coil has been fitted.
Should you see this message for any other reason, especially when reinstalling the same coil that is still warm after use. If so, rotate the regulation ring counterclockwise so that the ‘basic resistance” won’t be reset.
4.Device Too Hot Alert: When the device’s inner temperature passes over 70℃, the output will shut off automatically and the screen will appear “Device Too Hot” for 5 seconds. After then, it switches back to normal.
5.Temperature Protection: Under VT mode, if the coil’s actual temperature reaches to the set temperature, the device will show “Temp Protection”.
6.Over 10s Protection: If you keep pressing the fire button for more than 10 seconds, the screen will appear “Over 10S”.
7.Atomizer Short-circuit Protection: When atomizer short-circuit occurs, the screen will appear “Atomizer Short”.
8.Atomizer Low Alert: When the atomizer resistance is lower than 0.4ohm under VW mode or lower than 0.2ohm under VT mode, “Atomizer Low” will appear on the screen.
9.Low-voltage Protection: When the battery voltage is lower than 3.3V, the screen will appear “Battery Low” and “Lock”. Thus the battery is locked. Recharging to unlock the battery.
1.Under VT mode, please install the temperature control coils at room temperature ;
2.Only use temperature control coils under VT mode. Damages will be caused when temperature control coils are accidentally used under VW mode.
3.VT mode only supports a maximum of 1.0ohm. It will automatically switch to VW mode when the coil is larger than 1.0ohm or using a normal coil under VT mode.
DOA (Dead on Arrival) ONLY!
Note: We now need serial number to proceed after-sales service. Please kindly preserve the serial number of product if it's available.
No Customer Review
Questions and answers about this item.Ask a Question
Is the tank plastic or glass16-02-03 10:30
Hi, it's a Pyrex Glass tank. Thanks for your attention.16-02-04 09:51
Does the eGrip-VT also require the silicone cap over the coil head like the eGrip-CL.16-01-04 18:37
Yes, it does. Thanks for your attention.16-01-05 09:22
When do you expect this Egrip OLED VT to come in?15-12-03 09:05
Sorry, we don't have a specific time yet. We're confirming with the factory now. Thanks for your attention.15-12-03 15:38