[Special Edition] 30W Eleaf iStick 2200mAh OLED Screen MOD Battery, genuine Eleaf products and same excellent performance, while with novel colors. It can also support sub ohm coil.
Notice: Eleaf now requires S/N (serial number) before providing replacements (due to counterfeits in market).
We recommend you to keep the packing boxes after you get parcel, or take a picture of SN before you discard it. Thank you!
Shipping restriction: due to exclusive distributor of Eleaf, we do not send Eleaf products to customers in South Korea, or UK.
[Special Edition] 30W Eleaf iStick Mod Battery
Product Introduction[Special Edition] 30W Eleaf iStick 2200mAh OLED Screen MOD Battery, genuine Eleaf products and same excellent performance, while with novel colors. It can also support sub ohm coil thus give you the best vaping experience.
Size (length x width x height): 32 x 20 x 77 mm
Color: blue and white porcelain, carbon fiber black, ripple waves and wood
Thread Type: 510 Thread
Variable voltage: 2.0V - 8V
Variable wattage: 5W - 30W
Mimimum resistance value: 0.4ohm
30W iStick battery comes with
Simple packing. Customary Packing from the factory, the packing is subject to change without notice.
4. Adjustable voltage
5. Spring connector
6. Pass-through function
7. High Stability: The output wattage is in high stability. It can also be up to the high output wattage even in the case of low power.
Switch the VV/VW mode: Press the square button for three times to switch the VV/VW mode when the battery is turned on. In VV mode, you can adjust output voltage between 2.0V-8.0V. In VW mode, you can adjust output wattage between 5W-30W.
Adjust the voltage/wattage: Press the up-and-down arrow buttons to increase or decrease the voltage/wattage. Keep pressing the up/down arrow button, voltage/wattage will increase or decrease slowly at first, then they will increase/decrease at a constant high speed. The number will stop increasing/decreasing when you loosen the up/down arrow button.
Lock and Unlock: Keep pressing up-arrow button and down-arrow button simultaneously for 2 seconds when the battery is on, then they will be locked and the screen will reflect “Lock”. Still keep pressing simultaneously for 2 seconds to unlock them and the screen will reflect “Unlock”. Through these operations, you can protect the buttons from unintentional presses and prolong their service life.
Switch the display mode: Keep pressing up-arrow button and down-arrow button simultaneously for 2 seconds when the battery is off, the screen display will rotate 180 degrees. You can view the screen from two kinds of angle through this operation.
How to charge: iStick 30W is charged through the Micro USB port at the bottom of battery.It will take 2.5 hours to fully charge the battery via 1A wall adaptor.The battery level indicator on the OLED screen will keep flashing during charging. When fully charged, the indicator will stop flashing and keep shining for 15 seconds then go out.
Over 10s Protection: If you keep pressing the button for over 10 seconds, the output will shut off and the OLED screen will reflect “Over 10s”.
Atomizer Short-circuit Protection: When atomizer short-circuit occurs, the OLED screen will reflect “Atomizer Short”.
Low-voltage Protection: When the voltage of battery is below 3.3V, the OLED screen will reflect “Lock”.
Unlock the Low-voltage Protection: When the voltage of battery is above 3.7V, the low-voltage protection will be unlocked.
Low power Alert: If the power of battery is lower than 10%, the power symbol on the screen will flash.
3 months. Pls check Guarantee Policy.
Note: We now need serial number to proceed after-sales service. Please kindly preserve the serial number of product if it's available.
I love the sleek and lighweigh design, and this novel color. It fits well in my hand and gives great flavor and draw. A very good device for beginners, in my opinion.
I bought 2 of this mod a month ago, one is for home use, another one is for work use. Have no any problem till now. I have recommend many of my friends to buy it.
Lost my old 30w istick
This is my first istick mod
I am a fan of Eleaf istick series. I have the 10 and 20 watt istick mods, but I just bought an Atlantis tank that use sub ohm coils. I need a more powerful mod to work with it. This 30w istick was my first choice. I am pleased with its performance.
Questions and answers about this item.Ask a Question