SMOK Micro One 150 TC Starter Kit


Product Introduction

SMOK Micro One 150 TC Starter Kit, includes R150 TC MOD and Minos tank. The compact size is pocket friendly and portable. Up to 150W output, R150 supports TC modes as well. With the large M2 deck, Minos sub-ohm tank can change to RTA easily. Micro One 150 kit brings wonderful vaping experience.


Parameters

R150 TC MOD

Size: 77 x 50 x 26.5 mm
Battery Capacity: 1900mAh
Voltage: 0.35V - 8.00V
Wattage Range: 6W - 150W
Temp Range: 200F -600F/ 100°C -315°C
Resistance Range: 0.06ohm - 3.0ohm (TC mode); 0.1ohm - 3ohm (VW mode)
Material: Aluminum Alloy and Zinc Alloy

Minos Sub tank

Size: 25 x 48mm
Capacity: 4ml
Material: Glass and Stainless Steel
Thread: 510

SMOK Micro One 150 TC Starter Kit - 1900mAh

Micro One 150 Kit comes with

  • 1 x R150 TC Box Mod (150W)
  • 1 x Minos Sub tank (25mm)
  • 1 x 0.3ohm Q2 core (pre-installed)
  • 1 x Minos M2 Deck
  • 1 x replacement glass tube
  • 1 x USB charging/Upgrading cable
  • 1 x User Manual
  • Spare Parts

SMOK Micro One 150 TC Starter Kit - 1900mAh

Simple packing. Customary packing from the factory, the packing is subject to change without notice.


Four eye catching colors
Compact size

Structural design
Adjustable initial resistance
Support SS/Ni200/Ti wire
Bottom adjustable airflow system

510 RDA drip tip
Top refill system

Big M2 build deck for RTA option

Multiple protections

  • Intelligent Atomizer Recognition
  • Puff monitoring system
  • 12 seconds cut-off
  • Short circuit protection
  • Over-heating protection
  • Low battery warning

SMOK Micro One 150 TC Starter Kit - 1900mAh


E-juice filling: Screw off the drip tip and top cap, then fill juice through 2 slots, and close the cap.

SMOK Micro One 150 TC Starter Kit - 1900mAh

How to replace

unscrew the atomizer base from the atomizer, then the atomizer head off the base, replace the new head to the base and screw them back onto the tank tube.

How to build the RTA(M2)

1. Before starting make sure your hands are clean.
2. Taking the Minos-RTA M2 deck apart.
3. Installing the pre-wrapped coil. Insert one end of your coil into the up-side screw, and the other end into the down-side screw.
4. Positioning and cutting the exceeding ends of wire off. Make sure the coil is fixed and lined up with the air hole, and also make sure the coil is NOT touching the deck. Then cut the exceeding ends of wire off.
5. Cutting a strip of cotton and make sure it's just larger than the coil you built.
6. Inserting the cotton, and placing it in the middle.
7. Cutting the wick at an angle and make sure it's not too short and not too long.

8. Wet the coil with your e-liquid and adjust the wick.

SMOK Micro One 150 TC Starter Kit - 1900mAh

Power on/off:
Press the Power Button 5 times in quick succession to turn the device on. When the device is locked, hold the Power Button for 5s.
When the device is unlocked: by pressing Power Button 5 times to exit the locked mode. Press the Power Button and - button simultaneously to switch between "WATT MODE",  "TEMP MODE"and "MEMORY MODE". Press the Power Button and + button simultaneously to switch between "MIN", "SOFT", "NORM", "HARD" and "MAX" draw effects. Press + button and - button simultaneously to switch between "TURN ON" and "TURN OFF". When the device is locked: Press + button and - button simultaneously to show daily vaping time and puff numbers.


  • No e-juice. You shall purchase it separately.

SMOK Micro One 150 TC Starter Kit - 1900mAh


3 months for R150 TC Mod. Please check guarantee policy.


Our images are copyrighted. It is forbidden to reprint without our permission.